Selection
Download Find products
Product Category
Need a technical consultant to answer your questions?
Contact phone number:020-32029929
Email:jetekps@jetekcn.com
IB1224SY-2WR1
● High efficiency, with low output ripple and noise.
● Stable voltage output within the rated range
- Product Description
- Parameter Introduction
- Precautions
-
● Small size, high power density
● High efficiency, with low output ripple and noise.
● Stable voltage output within the rated range
● Low no-load power consumption and low quiescent current.
● Long-duration short-circuit protection
● Good thermal stability and excellent temperature characteristics.
● Operating temperature range: -40℃~ 85℃
● Isolation voltage up to 1500 VDC
● High reliability ( MTTF ≥ 350 Ten thousand hours)
● International Standard SIP Packaging, cost-saving PCB Installation space
● Eco-friendly design, compliant with RoHS Instruction
● 100 % Full-load aging
-
Product Model List
Model number
Rated Input Voltage (V)
Rated output
Typical Efficiency (%)
Maximum capacitive load
(uF)
Nominal
Scope
Voltage (V)
Current (mA)
IB0503SY-2WR1
5
4.75~5.25
3.3
606
62
2200
IB0505SY-2WR1
5
400
74
2200
IB0512SY-2WR1
12
167
82
1000
IB0524SY-2WR1
24
83
76
820
IB1205SY-2WR1
12
11.4–12.6
5
400
72
2200
IB1212SY-2WR1
12
167
82
1000
IB1224SY-2WR1
24
83
76
820
IB1505SY-2WR1
15
14.25~15.75
5
400
71
2200
IB1512SY-2WR1
12
167
81
100
IB1515SY-2WR1
15
133
80
1000
IB1524SY-2WR1
24
83
72
1000
IB2405SY-2WR1
24
22.8~25.2
5
400
76
2200
IB2412SY-2WR1
12
167
73
1000
IB2415SY-2WR1
15
133
78
1000
Output characteristics
Project
Conditions
smallest
Typical
Maximum
Unit
Output power
0.2
2
W
Line regulation of voltage
Under rated load, the input voltage varies by ±1%.
±0.5
%
Load Regulation Rate
Under nominal input conditions, the load varies from 10% to 100%.
±2
Output voltage accuracy
100% load
±3
Quiescent current
Under nominal input, with the output load at 0 Ω.
IB05XX
≤20
mA
Other
≤ 10
Temperature drift coefficient
Under rated load
±0.03
%/°C
Ripple & Noise
Bandwidth: 20 MHz, using the parallel‑line method.
30
60
mVp-p
Switching frequency
Rated input voltage
250
KHz
Output short-circuit protection
Long-duration short-circuit protection
Input filter
Capacitor filtering
Hot-swappable
Not supported
Project
Test conditions
smallest
Typical
Maximum
Unit
Insulation resistance
500VDC
1000
MΩ
Insulation voltage
Test duration: 1 minute; leakage current less than 1 mA.
1500
VDC
General Characteristics
Project
Conditions
smallest
Typical
Maximum
Unit
Storage humidity
5
95
%
Operating temperature
-40
85
°C
Storage temperature
-55
125
Case temperature rise during operation
15
25
Pin soldering temperature resistance
Solder joint is 1.5 mm from the housing; apply for 10 seconds.
300
MTTF
MIL-HDBK-217F@25℃
350
Ten thousand hours
Weight
2.5
Kerl
Cooling method
Natural air cooling
Housing material
Flame-retardant, heat-resistant plastic (UL94-V0)
-
Avoid operating under no-load conditions whenever possible: When the load power consumption is less than the module’s rated output power of 10% It is recommended to connect a dummy load at the output or to select one with a lower rated power. of the module, the dummy load (resistor) can be set to 10% of the module’s rated power. % Calculate the resistance value R = U 2 /(10 % ×2W );
Avoid excessively large output bypass capacitors: The external capacitor C2 at the output should not have an excessively large capacitance; otherwise, it may cause overcurrent during module startup or result in poor startup performance. Specifically, Selection should be based on the external capacitance meter.
This product series does not support hot-swapping on the input side or parallel operation on the output side.
For applications with stringent ripple noise requirements, an external LC filter should be connected. Filter circuit, L C The resonant frequency of the filter must be much lower than the DC/ DC The switching frequency of the module, Prevention To prevent mutual interference that could increase output ripple or damage the module, as shown in the figure:
Keywords:
Related products
We look forward to your call.
You can also submit your information online, and we will get back to you within 24 hours!
Guangzhou Company
Company Address: Building 2, Hesheng Plaza, No. 16 Caipin Road, Huangpu District, Guangzhou
Email:jetekps@jetekcn.com
Chongqing Factory
Company Address: No. 20, Shilidian Road, Dazu Industrial Park, Chongqing City
Email:jetekps@jetekcn.com