Selection
Download Find products
Product Category
Need a technical consultant to answer your questions?
Contact phone number:020-32029929
Email:jetekps@jetekcn.com
IA0512SY-1WR1
● High efficiency with low output ripple and noise
● Low no-load power consumption and low quiescent current
- Product Description
- Parameter Introduction
- Precautions
-
● Small size, high power density● High efficiency, low output ripple noise.● Low no-load power consumption and low quiescent current.● Long-duration short-circuit protection with auto-recovery● Good thermal stability and excellent temperature characteristics.● Operating temperature range: -40°C to +85°C● Isolation voltage up to 1500 VDC● High reliability (MTTF ≥ 3.5 million hours)● International standard DIP package, saving PCB mounting space.● Environmentally friendly design, compliant with the RoHS Directive.● 100% Full-load aging
-
Product Model List
Model number
Rated Input Voltage (V)
Rated output
Typical Efficiency (%)
Maximum capacitive load
(uF)
Nominal
Scope
Voltage (V)
Current (mA)
IA0505SY-1WR1
5
4.75~5.25
±5
±100
59
1000
IA0509SY-1WR1
±9
±56
63
1000
IA0512SY-1WR1
±12
±42
66
680
IA0515SY-1WR1
±15
±33
68
680
IA1205SY-1WR1
12
11.4–12.6
±5
±100
59
1000
IA1209SY-1WR1
±9
±56
63
1000
IA1212SY-1WR1
±12
±42
66
1000
IA1215SY-1WR1
±15
±33
66
680
IA1224SY-1WR1
±24
±21
66
680
IA2405SY-1WR1
24
22.8~25.2
±5
±100
59
1000
IA2409SY-1WR1
±9
±56
66
1000
IA2412SY-1WR1
±12
±42
64
1000
IA2415SY-1WR1
±15
±33
65
1000
IA2424SY-1WR1
±24
±21
66
680
Note: * The capacitive load is the same for both the positive and negative outputs. Output characteristics
Project
Conditions
Minimum
Typical
Maximum
Unit
Output power
0.1
1
W
Line regulation of voltage
Under rated load, the input voltage varies by ±1%.
±0.5
%
Load Regulation Rate
Under nominal input conditions, the load varies from 10% to 100%.
±2
Output voltage accuracy
100% load
±3
Quiescent current
Under nominal input, with the output load at 0 Ω.
IA05XX
≤12
mA
Other
≤8
Temperature drift coefficient
Under rated load
±0.03
%/°C
Ripple & Noise
Bandwidth: 20 MHz, using the parallel-line method.
30
60
mVp-p
Switching frequency
Rated input voltage
280
KHz
Output short-circuit protection
Long-duration short-circuit protection
Input filter
Capacitor filtering
Hot-swappable
Not supported
Insulation properties
Project
Test conditions
Minimum
Typical
Maximum
Unit
Insulation resistance
500VDC
1000
MΩ
Insulation voltage
Test duration: 1 minute; leakage current less than 1 mA.
1500
VDC
General Characteristics
Project
Conditions
Minimum
Typical
Maximum
Unit
Storage humidity
5
95
%
Operating temperature
-40
85
°C
Storage temperature
-55
125
Case temperature rise during operation
15
25
Pin soldering temperature resistance
Solder joint is 1.5 mm from the housing; apply for 10 seconds.
300
MTTF
MIL-HDBK-217F@25℃
350
Ten thousand hours
Weight
4.4
Kerl
Cooling method
Natural air cooling
Housing material
Flame-retardant, heat-resistant plastic (UL94-V0)
-
Avoid operating under no-load conditions whenever possible: When the load power consumption is less than 10% of the module’s rated output power. % It is recommended to connect a dummy load at the output or to select modules with a lower rated power; the dummy load (resistor) can be set to 10% of the module’s rated power. % Calculate the resistance value R = U 2 /(10 % ×1W);Avoid excessively large output bypass capacitors: The external capacitor C2 at the output should not have an excessively large capacitance; otherwise, it may cause overcurrent during module startup or result in poor startup performance. The specific value should be selected based on the capacitor’s datasheet.This product series does not support hot-swapping on the input side or parallel operation on the output side.In applications with stringent ripple‑noise requirements, an external LC filter should be used. The resonant frequency of the LC filter must be significantly lower than the switching frequency of the DC/DC converter to prevent mutual interference that could increase output ripple or damage the module, as shown in the figure.
Keywords:
Related products
We look forward to your call.
You can also submit your information online, and we will get back to you within 24 hours!
Guangzhou Company
Company Address: Building 2, Hesheng Plaza, No. 16 Caipin Road, Huangpu District, Guangzhou
Email:jetekps@jetekcn.com
Chongqing Factory
Company Address: No. 20, Shilidian Road, Dazu Industrial Park, Chongqing City
Email:jetekps@jetekcn.com