Selection
Download Find products
Product Category
Need a technical consultant to answer your questions?
Contact phone number:020-32029929
Email:jetekps@jetekcn.com
IF0524DY-2WR1
● High efficiency, with low output ripple and noise.
● Stable voltage output within the rated range
- Product Description
- Parameter Introduction
- Precautions
-
● Small size, high power density● High efficiency with low output ripple and noise.● Stable voltage output within the rated range● Low no-load power consumption and low quiescent current.● Long-duration short-circuit protection and● Good thermal stability and excellent temperature characteristics.● Operating temperature range: -40°C to 85°C● Isolation voltage up to 3000 VDC● High reliability (MTTF ≥ 3.5 million hours)● International standard DIP package, saving PCB mounting space.● Environmentally friendly design, compliant with the RoHS Directive.● 100% Full-load aging
-
Product Model List
Model number
Rated Input Voltage (V)
Rated output
Typical Efficiency (%)
Maximum capacitive load
(uF)
Nominal
Scope
Voltage (V)
Current (mA)
IF0505DY-2WR1
5
4.75~5.25
5
400
70
2200
IF0512DY-2WR1
12
167
75
1000
IF0524DY-2WR1
24
83
78
1000
IF1205DY-2WR1
12
11.4~12.
5
400
73
2200
IF1209DY-2WR1
9
222
75
2200
IF1212DY-2WR1
12
167
75
1000
IF1224DY-2WR1
24
83
72
1000
IF1505DY-2WR1
15
14.25~15.75
5
400
71
2200
IF1524DY-2WR1
24
83
72
1000
IF2405DY-2WR1
24
22.8~25.2
5
400
72
2200
IF2412DY-2WR1
12
167
75
1000
IF2424DY-2WR1
24
83
71
1000
Output characteristics
Project
Conditions
Minimum
Typical
Maximum
Unit
Output power
0.2
2
W
Line regulation of voltage
Under rated load, the input voltage varies by ±1%.
±0.5
%
Load Regulation Rate
Under nominal input conditions, the load varies from 10% to 100%.
±2
Output voltage accuracy
100% load
±3
Quiescent current
Under nominal input, with the output load at 0 Ω.
IF05XX
≤20
milliampere
Other
≤ 10
Temperature drift coefficient
Under rated load
±0.03
%/°C
Ripple & Noise
Bandwidth: 20 MHz, using the parallel‑line method.
30
60
mVp-p
Switching frequency
Rated input voltage
100
KHz
Output short-circuit protection
Long-duration short-circuit protection
Input filter
Capacitor filtering
Hot-swappable
Not supported
Insulating properties
Project
Test conditions
Minimum
Typical
Maximum
Unit
Insulation resistance
500VDC
1000
MΩ
Insulation voltage
Test duration: 1 minute; leakage current less than 1 mA.
3000
VDC
General Characteristics
Project
Conditions
Minimum
Typical
Maximum
Unit
Storage humidity
5
95
%
Operating temperature
-40
85
°C
Storage temperature
-55
125
Case temperature rise during operation
15
25
Pin soldering temperature resistance
Solder joint is 1.5 mm from the housing; apply for 10 seconds.
300
MTTF
MIL-HDBK-217F@25℃
350
Ten thousand hours
Weight
2.8
Kerl
Cooling method
Natural air cooling
Housing material
Flame-retardant, heat-resistant plastic (UL94-V0)
-
Avoid operating under no-load conditions whenever possible: When the load power consumption is less than the module’s rated output power of 10% , it is recommended to connect a dummy load at the output or to select one with a lower rated power. of the module, the dummy load (resistor) can be set to 10% of the module’s rated power. % Calculate: resistance value R = U 2 /(10 % ×1W );
Avoid excessively large output bypass capacitors: The external capacitor C2 at the output should not have an excessively large capacitance; otherwise, it may cause overcurrent during module startup or result in poor startup performance. Specifically, Selection should be based on the external capacitance meter.
This product series does not support hot-swapping on the input side or parallel operation on the output side.
For applications with stringent ripple noise requirements, an external LC filter should be connected. Filter circuit, LC The resonant frequency of the filter must be much lower than the DC/ D C The switching frequency of the module, prevention To prevent mutual interference that could increase output ripple or damage the module, as shown in the figure:
Keywords:
Related products
We look forward to your call.
You can also submit your information online, and we will get back to you within 24 hours!
Guangzhou Company
Company Address: Building 2, Hesheng Plaza, No. 16 Caipin Road, Huangpu District, Guangzhou
Email:jetekps@jetekcn.com
Chongqing Factory
Company Address: No. 20, Shilidian Road, Dazu Industrial Park, Chongqing City
Email:jetekps@jetekcn.com