Selection
Download Find products
Product Category
Need a technical consultant to answer your questions?
Contact phone number:020-32029929
Email:jetekps@jetekcn.com
J10W24D03EE
● Ultra-wide voltage input 4:1
● No external components required
● Continuous short-circuit protection (self-resetting)
- Product Description
- Parameter Introduction
- Precautions
-
● High efficiency, low output ripple noise.● Ultra-wide voltage input 4:1● No external components required.● Continuous short-circuit protection (self-resetting)● Operating temperature range: -40°C to +85°C● Isolation voltage up to 1500 VDC● Metallic shielding package● High reliability (MTTF ≥ 1 million hours)● International standard pin configuration● 100% full-load aging
-
Model number Nominal Scope Maximum Voltage (V) Current (mA) Minimum Maximum Minimum Typical J10W24D03EE 24
9~36
40
±3.3 0 ±1515 78 80 2200 J10W24D05EE ±5 0 ±1000 80 81 1000 J10W24D09EE ±9 0 ±556 82 86 680 J10W24D12EE ±12 0 ±416 84 87 470 J10W24D15EE ±15 0 ±333 85 88 330 J10W24D24EE ±24 0 ±208 85 87 220 J10WV24S03EE 3.3 0 3030 78 81 3300 J10W24S05EE 5 0 2000 81 84 2200 J10W24S09EE 9 0 1111 83 86 1000 J10W24S12EE 12 0 833 84 87 680 J10W24S15EE 15 0 667 85 88 470 J10W24S24EE 24 0 417 85 87 220 J10W48D03EE 48
18~72
75
±3.3 0 ±1515 78 81 2200 J10W48D05EE ±5 0 ±1000 81 84 1000 J10W48D09EE ±9 0 ±556 83 86 680 J10W48D12EE ±12 0 ±416 84 87 470 J10W48D15EE ±15 0 ±333 85 88 330 J10W48D24EE ±24 0 ±208 85 88 220 J10W48S03EE 3.3 0 3030 78 80 3300 J10W48S05EE 5 0 2000 81 84 2200 J10W48S09EE 9 0 1111 83 86 1000 J10W48S12EE 12 0 833 85 88 680 J10W48S15EE 15 0 667 85 88 470 J10W48S24EE 24 0 417 86 88 220 Output characteristics
Project
Conditions
Minimum
Typical
Maximum
Unit
Output power
0
10
W
Output positive voltage accuracy
±1
±2
%
Output negative voltage accuracy
±2
±3
Line regulation of voltage
Full load, input voltage variation from low to high
±0.2
±0.5
Load Regulation Rate
Under nominal input conditions, the load varies from 10% to 100%.
±0.5
±1
Temperature drift coefficient
Under rated load
±0.03
%/°C
Ripple & Noise
Bandwidth: 20 MHz, using the parallel‑line method.
50
100
mVp-p
Switching frequency
Rated input voltage
320
350
KHz
Output short-circuit protection
Continuous short-circuit protection (self-resetting)
Input Filtering Type
Pi-type filter
Hot-swappable
Not supported
Remote Control end CTRL
Module enabled
The CTRL pin is either left floating or connected to a high level (3.3–12.0 VDC).
Module closed
Connect the CTRL pin to GND or to a low-level signal (0–1.2 VDC).
The CTRL pin voltage is referenced to the input-side GND. Input characteristics
Project
Conditions
Minimum
Typical
Maximum
Unit
Input Undervoltage Protection
24 VDC input
6.6
7.3
VDC
48VDC input
13.5
14.8
Starting voltage
24 VDC input
8.2
48VDC input
16.2
18
Impulse Voltage (1 sec. max)
24 VDC input
-0.7
50
48VDC input
100
No-load current
24 VDC input
5
10
mA
48VDC input
3
5
EMC characteristics
EMI
Conducted interference
Radiated interference
CISPR 32/EN 55032 Class B (see EMI circuit recommendations for details)
EMS
Electrostatic discharge
IEC/EN61000-4-2 CONTACT ±4kV
Radiation immunity
IEC/EN61000-4-3 10V/M
Pulse group immunity
IEC/EN 61000-4-4 ±2 kV (see EMS circuit recommendations for details)
Surge immunity
IEC/EN 61000-4-5 Line-to-Line ±2 kV (see EMS circuit recommendations for details)
Conducted Emission Immunity
IEC/EN61000-4-6 3 VR. M. S
Immunity to voltage sags, dips, and short interruptions
IEC/EN61000-4-29 0%, 70%
Insulation properties
Project
Test conditions
Minimum
Typical
Maximum
Unit
Insulation resistance
Input–output, insulation voltage 500 VDC
1000
MΩ
Insulation voltage
Input–output, test duration: 1 minute, leakage current less than 1 mA.
1500
VDC
Input/Output – Enclosure, test duration: 1 minute, leakage current less than 1 mA.
1000
General Characteristics
Project
Conditions
Minimum
Typical
Maximum
Unit
Storage humidity
No condensation
5
95
%
Operating temperature
-40
85
°C
Storage temperature
-55
125
Case temperature rise during operation
20
30
Pin soldering temperature resistance
Solder joint is 1.5 mm from the housing; apply for 10 seconds.
300
MTTF
MIL-HDBK-217F@25℃
100
Ten thousand hours
Weight
18
Kerl
Cooling method
Natural air cooling
Housing material
Black metal casing
-
Avoid operating under no-load conditions whenever possible: The external capacitor C3 at the output should not have an excessively large capacitance; otherwise, it may cause overcurrent during module startup or result in poor start-up performance. The specific value should be selected based on the capacitor’s datasheet.
The product does not support parallel operation for power boosting.
In applications with stringent ripple‑noise requirements, an external LC filter should be used. The resonant frequency of the LC filter must be significantly lower than the switching frequency of the DC/DC converter to prevent mutual interference that could increase output ripple or damage the module, as shown in the figure.
Keywords:
Related products
We look forward to your call.
You can also submit your information online, and we will get back to you within 24 hours!
Guangzhou Company
Company Address: Building 2, Hesheng Plaza, No. 16 Caipin Road, Huangpu District, Guangzhou
Email:jetekps@jetekcn.com
Chongqing Factory
Company Address: No. 20, Shilidian Road, Dazu Industrial Park, Chongqing City
Email:jetekps@jetekcn.com