Selection
Download Find products
Product Category
Need a technical consultant to answer your questions?
Contact phone number:020-32029929
Email:jetekps@jetekcn.com
J15W48S05AE
● Ultra-wide voltage input 4:1
● No external components required
● Continuous short-circuit protection (self-resetting)
- Product Description
- Parameter Introduction
- Precautions
-
● High efficiency, low output ripple noise.● Ultra-wide voltage input 4:1● No external components required.● Continuous short-circuit protection (self-resetting)● Operating temperature range: -40°C to +85°C● Isolation voltage up to 1500 VDC● Metallic shielding package● High reliability (MTTF ≥ 1 million hours)● International standard pin configuration● 100% full-load aging
-
Model number
Rated Input Voltage (V)
Rated output
Typical Efficiency (%)
Maximum capacitive load
(uF)
Nominal
Scope
Maximum
Voltage (V)
Current (mA)
smallest
Maximum
smallest
Typical
J15W24D05AE
24
9~36
40
±5
0
±1500
83
86
4700
J15W24D09AE
±9
0
±833
84
87
2200
J15W24D12AE
±12
0
±625
86
88
1000
J15W24D15AE
±15
0
±500
86
89
820
J15W24D24AE
±24
0
±313
87
89
680
J15W24S03AE
3.3
0
4545
84
86
4700
J15W24S05AE
5
0
3000
83
85
4700
J15W24S09AE
9
0
1667
85
87
3300
J15W24S12AE
12
0
1250
86
88
2200
J15W24S15AE
15
0
1000
87
89
1000
J15W24S24AE
24
0
625
87
89
820
J15W48D05AE
48
18~72
75
±5
0
±1500
83
86
4700
J15W48D09AE
±9
0
±833
84
87
2200
J15W48D12AE
±12
0
±625
86
88
1000
J15W48D15AE
±15
0
±500
86
89
820
J15W48D24AE
±24
0
±313
87
89
470
J15W48S03AE
3.3
0
4545
84
86
4700
J15W48S05AE
5
0
3000
83
85
4700
J15W48S09AE
9
0
1667
85
87
3300
J15W48S12AE
12
0
1250
86
88
2200
J15W48S15AE
15
0
1000
87
89
1000
J15W48S24AE
24
0
625
87
89
820
Note: * The capacitive load is the same for both the positive and negative outputs. Output characteristics
Project
Conditions
smallest
Typical
Maximum
Unit
Output power
0
15
W
Output positive voltage accuracy
±1
±2
%
Output negative voltage accuracy
±2
±3
Line regulation of voltage
Full load, input voltage variation from low to high
±0.2
±0.5
Load Regulation Rate
Under nominal input conditions, the load varies from 10% to 100%.
±0.5
±1
Temperature drift coefficient
Under rated load
±0.03
%/°C
Ripple & Noise
Bandwidth: 20 MHz, using the parallel‑line method.
50
100
mVp-p
Switching frequency
Rated input voltage
320
320
KHz
Output short-circuit protection
Continuous short-circuit protection (self-resetting) Input Filtering Type
Pi-type filter Hot-swappable
Not supported Input characteristics
Project
Conditions
smallest
Typical
Maximum
Unit
Input undervoltage protection
24 VDC input
6.6
7.3
VDC
48VDC input
13.5
14.8
Starting voltage
24 VDC input
48VDC input
16.2
18
Impulse Voltage (1 sec. max)
24 VDC input
-0.7
50
48VDC input
10
No-load current
24 VDC input
5
10
mA
48VDC input
4
8
EMC characteristics
EMI
Conducted interference
Radiated interference
CISPR 32/EN 55032 Class B (see EMI circuit recommendations for details)
EMS
Electrostatic discharge
IEC/EN61000-4-2 CONTACT ±4kV
Radiation immunity
IEC/EN61000-4-3 10V/M
Pulse group immunity
IEC/EN 61000-4-4 ±2 kV (see EMS circuit recommendations for details)
Surge immunity
IEC/EN 61000-4-5 Line-to-Line ±2 kV (see EMS circuit recommendations for details)
Conducted Emission Immunity
IEC/EN61000-4-6 3 VR. M. S
Immunity to voltage sags, dips, and short-duration interruptions
IEC/EN61000-4-29 0%, 70%
Insulating properties
Project
Test conditions
smallest
Typical
Maximum
Unit
Insulation resistance
Input–output, insulation voltage 500 VDC
1000
MΩ
Insulation voltage
Input–output, test duration: 1 minute, leakage current less than 1 mA.
1500
VDC
Input/Output – Enclosure, test duration: 1 minute, leakage current less than 1 mA.
1000
General Characteristics
Project
Conditions
smallest
Typical
Maximum
Unit
Storage humidity
No condensation
5
95
%
Operating temperature
-40
85
°C
Storage temperature
-55
125
Case temperature rise during operation
20
35
Pin soldering temperature resistance
Solder joint is 1.5 mm from the housing; apply for 10 seconds.
300
MTTF
MIL-HDBK-217F@25℃
100
Ten thousand hours
Weight
18
Kerl
Cooling method
Natural air cooling
Housing material
Black metal casing
-
Avoid operating under no-load conditions whenever possible: The external capacitor C2 at the output should not have an excessively large capacitance; otherwise, it may cause overcurrent during module startup or result in poor start-up performance. The specific value should be selected based on the capacitor’s datasheet.
The product does not support parallel operation for power boosting.
In applications with stringent ripple‑noise requirements, an external LC filter should be used. The resonant frequency of the LC filter must be significantly lower than the switching frequency of the DC/DC converter to prevent mutual interference that could increase output ripple or damage the module, as shown in the figure.
Keywords:
Related products
We look forward to your call.
You can also submit your information online, and we will get back to you within 24 hours!
Guangzhou Company
Company Address: Building 2, Hesheng Plaza, No. 16 Caipin Road, Huangpu District, Guangzhou
Email:jetekps@jetekcn.com
Chongqing Factory
Company Address: No. 20, Shilidian Road, Dazu Industrial Park, Chongqing City
Email:jetekps@jetekcn.com